Stretch and strengthen your forearms and wrists.
[6]
1. A setup begins with a preliminary,hands-on inspection of your bass.Check playability and listen for issueslike buzzing frets and hardwarerattles. List any problems you find.![Bass guitar tapping tab Bass guitar tapping tab](/uploads/1/2/4/9/124913062/753522083.jpg)
2. To gauge the amount of relief in your neck, use both hands to simultaneouslyfret the 4th string at the 1st fret and somewhere between the 14thand 16th frets. At the mid point between these two fretted notes, look atthe gap between the bottom of the string and the top of the frets. To getanother perspective on this gap, bounce the string against the frets withyour picking-hand index finger.3. Stretch your pickinghand across the fretboardwith your thumb aimingtowards the bridge andindex finger extendedtoward the nut (Photo2). Open your hand asfar as you can comfortablystretch and fret thelowest string with yourthumb. The object is tomove your thumb as closeto the bridge as you can,while allowing your indexfinger to touch the loweststring approximately halfwaybetween your frettingfinger at the 1st fret andpicking hand thumb.(Depending on the fretboardscale length, mypicking hand thumb landson the 14th, 15th, or16th fret.) Now the loweststring is fretted at twopoints with two hands.With the lowest stringsecured at the 1st and, say,15th fret, you can now useit as a straightedge.
4. With your picking-handindex finger, tap the stringagainst the middle frets.By repeatedly tapping andreleasing, you’ll be able togauge how much space liesbetween the bottom of thestring and the top of thosefrets. The gap (if any) isthe amount of relief. Howmuch of a gap you needdepends very much onyour playing style, butto get started, I adjust aninstrument to have a gapthat’s equivalent to thethickness of one or twobusiness cards.
3. To remove the neck to expose atruss rod that’s installed at the heel,take off the strings and back outthe screws at the neck plate.4. Once the screws have releasedthe neck, gently pull it free from thebody being careful not to scratchthe neck on the exposed screwtips.
5. Truss rods accessed at theneck heel are often adjusted with ascrewdriver. 6. Whether the trussrod is installed at the headstock orneck heel, the vast majority adjustclockwise to tighten and counterclockwiseto loosen.
7. To reattachthe neck, carefully place the heelinto the neck pocket and then insertthe screws by hand, slipping themthrough the body and seating thetips into their respective holes. 8.Tighten the neck screws securely.As you do this, use your free handto control the screwdriver tip so itdoesn’t slip out and mar the body.
6 – Bass Guitar Tapping Technique For Fast Shredding And Speed The bass guitar tapping technique is actually originated from the guitar. Back in the 80’s, Eddie Van Halen popularized this technique in his slick sounding solos. It has since been evolved and used in other instruments too. 7 – Correct Techniques And Methods of Using Your Fingers. This is the first in a series of lessons on tapping and related techniques for bass guitar. I hope to explain both the physical side of things, and so.
Your wrists and forearms will definitely get a workout from extended bass playing. Strong, flexible forearms and wrists help you avoid injury or painful conditions, such as carpal tunnel syndrome.- Lessons - Bass - 8 Finger Tapping guitar pro tab with free online tab player, speed control and loop. Download original Guitar Pro tab.
- This lesson deals with contrapuntal tapping for bass guitar whereby we play independent lines in both hands. This often involves a bass ostinato in the fretting hand and a melody in the right hand. The exercises provided aim to improve rhythmic independence between the hands by working on two lines one note at a time. Key: T = Tap.
- If you look up the history of the bass guitar, most online references say that it begins in the 1950s with the Fender Precision electric bass. While that’s partially true, the history of the bass guitar began long before that. The Fender Precision was the first mass-produced and widely distributed electric bass, but it wasn’t the first ever made.
![Bass Bass](/uploads/1/2/4/9/124913062/179601480.jpg)
- One good exercise is to hold your arm out in front of you with your elbow straight and your palm facing up. Reach over with your other hand and gently pull your hand down until you feel a stretch. Hold for 10 to 15 seconds, then do the same exercise with your other hand. Repeat 3 times with each hand.
- If you pull down you also want to push back. Hold your arm out in front of you with your elbow straight and your palm facing down. Pull your palm back towards your body with your other hand, until you feel a stretch. Hold for 10 to 15 seconds, then do the same exercise with your other hand. Repeat 3 times with each hand.
- You also want to strengthen the fingers of your fretting hand. You can find single-string permutations online that will help with this.[7]
I’ve read many articles and repairmanuals on bass setup, and I’vepersonally set up thousands of bassesas a professional. So when PG askedme to write a DIY piece on the subject,I thought, “What can I bring to thisdiscussion that’s truly helpful? Is there alittle something I can describe that youdon’t already know?”
In this article, we’ll cover the essentialswith the goal of helping you decide whatyou can handle yourself and what youshould leave to your local repair technician.Even if there are aspects of thejob you’re not prepared to attempt onyour own, it’s good to understand what’sinvolved with a bass setup. Knowing thesteps and terminology will let you communicatemore confidently and effectivelywith your repair guy or gal.
More than likely you’re thinkingabout setup because in some way, yourinstrument is not performingthe way you’d like. To pinpointany problems, we need to lookat all the factors that affect yourinstrument’s overall playability,sound, and function.
Preliminary Inspection
Our journey begins with ageneral inspection (Photo1), which consists of playingthe instrument while askingyourself these questions: Is theaction too high? Too low? Arethere buzzing frets? If so, thatindicates a need for adjustment.
Our journey begins with ageneral inspection (Photo1), which consists of playingthe instrument while askingyourself these questions: Is theaction too high? Too low? Arethere buzzing frets? If so, thatindicates a need for adjustment.
1. A setup begins with a preliminary,hands-on inspection of your bass.Check playability and listen for issueslike buzzing frets and hardwarerattles. List any problems you find.
While you’re at it, workthe volume and tone controls,checking for noise. Gently jigglethe 1/4' plug at the output jackto check it for noise. Are thereany hardware-related rattles?Take notes on all your observationsand list any issues youneed to address.
After you’ve given your bass ahands-on evaluation, you’re readyto get to work on the setup.
![Bass guitar tapping tab Bass guitar tapping tab](/uploads/1/2/4/9/124913062/753522083.jpg)
Tip: Because the adjustmentsthat control playability areaffected by string gauge andtension, be sure your bass sportsthe type of strings you plan touse. If you change string gauge,you’ll need to do a fresh setup toaccommodate the new strings.
Step 1: Measurethe Neck Relief
We start with checking the“relief” or amount of bend in theneck. I often see people sightingdown the neck from all anglesand making some very ballparkassessments about neck relief.But the precise and accurate wayto measure relief is to use thestrings as a straightedge. Here’show to measure neck relief:
1. Tune your bass to pitch.Use the primary tuning youput this instrument in whenperforming or recording.
2. With your fretting hand,hold your lowest stringagainst the 1st fret as if youwere playing that note.
2. With your fretting hand,hold your lowest stringagainst the 1st fret as if youwere playing that note.
2. To gauge the amount of relief in your neck, use both hands to simultaneouslyfret the 4th string at the 1st fret and somewhere between the 14thand 16th frets. At the mid point between these two fretted notes, look atthe gap between the bottom of the string and the top of the frets. To getanother perspective on this gap, bounce the string against the frets withyour picking-hand index finger.
4. With your picking-handindex finger, tap the stringagainst the middle frets.By repeatedly tapping andreleasing, you’ll be able togauge how much space liesbetween the bottom of thestring and the top of thosefrets. The gap (if any) isthe amount of relief. Howmuch of a gap you needdepends very much onyour playing style, butto get started, I adjust aninstrument to have a gapthat’s equivalent to thethickness of one or twobusiness cards.
Tip: Make sure you continuallycheck the tuningof your bass so it stays atpitch. This is crucial formaking accurate measurementsand adjustments.
Step 2:Adjust the Truss Rod
This is very important: If youdon’t feel comfortable adjustingyour truss rod or don’t have theproper tool, take this to yourlocal qualified repair technician.You can really mess upyour instrument by strippingthe threads on your truss rodor over tightening and breakingthis critical part of theneck. Whether the truss rodis adjusted via a male hex nut,a female socket, or a Phillipsnut at the neck heel, make sureyour tool has a snug fit so youdon’t strip out this vital part.
3. To remove the neck to expose atruss rod that’s installed at the heel,take off the strings and back outthe screws at the neck plate.4. Once the screws have releasedthe neck, gently pull it free from thebody being careful not to scratchthe neck on the exposed screwtips.
The vast majority of trussrods adjust clockwise totighten and counter-clockwiseto loosen. If your truss rod islocated at the headstock, lookdown the neck from headstockto body to determine clockwiseand counter-clockwisedirection. If your truss rodadjustment is at the heel of theneck, you’ll need to remove it(Photos 3 and 4). The movementswill be the same whenyou look from the heel down
Movie special effects software. Tip: If you have any doubts abouthow to adjust a truss rod, get a guitarrepair book or study the manualthat came with your instrument.Many manufacturers offer freeonline instructions for adjusting thetruss rods on their guitars.
If you decide you want tochange the gap between thestring and fret, here’s the process:
1. To reduce the gap betweenstring and fret, tighten thetruss rod. Conversely, toincrease the space betweenstring and fret, loosenit. Move the truss rod inquarter-turn increments.
2. Retune and recheck reliefeach time you move the rod.
2. Retune and recheck reliefeach time you move the rod.
Continue the processuntil you get the desiredgap between the string andfret. Again, unless you havea specific gap in mind,shoot for the thickness ofone or two business cards.
5. Truss rods accessed at theneck heel are often adjusted with ascrewdriver. 6. Whether the trussrod is installed at the headstock orneck heel, the vast majority adjustclockwise to tighten and counterclockwiseto loosen.
If your bass requiresadjustments at the neckheel (Photos 5 and 6),rather than the headstock,you’ll face the tediousprospect of reinstalling theneck and restringing tocheck each adjustment.
Tip: If your truss rod seems verydifficult to adjust, or stops moving,or makes a loud noise, see alocal repair tech. Although adjustinga truss rod may be foreignto you, all qualified techniciansunderstand how it functions. It’sdefinitely worth paying the priceto have this done right. Bobcad support.
Schecter Research 6 String Bass Guitar Tapping
There are several adjustmentsthat affect action,but they need to be done inthe correct order. Becauseyour decisions about allthe other action-relatedadjustments are based onneck relief, it’s importantto deal with the truss rodfirst. Once you’ve made anynecessary truss-rod adjustments,you’re ready to moveon to the other factors thatcontrol playability.
7. To reattachthe neck, carefully place the heelinto the neck pocket and then insertthe screws by hand, slipping themthrough the body and seating thetips into their respective holes. 8.Tighten the neck screws securely.As you do this, use your free handto control the screwdriver tip so itdoesn’t slip out and mar the body.
Bass Tapping Solo
If you’ve removed theneck to make truss rodadjustments, reattach itnow (Photos 7 and 8),restring, and retune.